How Many Pavers per Square Foot? (Chart by Size)
By Rowan Plank · Published September 28, 2026
The number of pavers per square foot is 144 ÷ (paver width × length in inches). A standard 4×8 in brick paver is 4.5 per square foot, a 6×6 is 4, and a 12×12 is 1. Multiply by your area in square feet, then add 5–10% for cuts.
Pavers per square foot by size
| Paver size (in) | Coverage per paver | Pavers per sq ft | Pavers for 100 sq ft |
|---|---|---|---|
| 4 × 8 | 0.22 sq ft | 4.5 | 450 |
| 6 × 6 | 0.25 sq ft | 4 | 400 |
| 6 × 9 | 0.375 sq ft | 2.67 | 267 |
| 12 × 12 | 1 sq ft | 1 | 100 |
| 12 × 24 | 2 sq ft | 0.5 | 50 |
| 16 × 16 | 1.78 sq ft | 0.56 | 57 |
| 24 × 24 | 4 sq ft | 0.25 | 25 |
These are nominal sizes, before extra for cuts. Rounded up to whole pavers.
Why your supplier's number may differ
Many pavers aren't exactly their nominal size. A "4×8" might really be 3⅞ × 7¾ in, or a metric 100 × 200 mm (about 3.94 × 7.87 in). That's about 4.6 per square foot instead of 4.5. Joints and spacer nubs also change the real coverage.
Oregon State Extension recommends using the coverage rate from your supplier, which is usually printed on the pallet or product page as pieces per square foot or square feet per pallet. If you have it, use it; if not, the table above is close enough to plan with.
How to calculate it yourself
- Measure the area. Length × width in feet. For an L-shaped patio, split it into rectangles and add them.
- Find pavers per square foot. 144 ÷ (width in × length in). For 6×9: 144 ÷ 54 = 2.67.
- Multiply. Area × pavers per sq ft.
- Add extra for cuts. Add 5%, or 10% if you have curves, circles or a herringbone or diagonal pattern (Oregon State Extension).
Example: a 12 × 14 ft patio in 4×8 pavers is 168 sq ft × 4.5 = 756 pavers, plus 10% for a herringbone pattern = 832 pavers.
Mixed-size patterns
Patterns that combine sizes (like a 6×6, 6×9 and 9×9 set) are usually sold by the square foot as a bundle. Buy by area, not by piece, and follow the manufacturer's pattern sheet.
Don't forget the base and sand
Pavers are only the top layer. Under them you need 4–6 in of compacted gravel and 1 in of bedding sand. For 100 sq ft, that's about 1.2 cubic yards of gravel at 4 in deep and 0.3 cubic yards of sand. See how deep to dig for pavers for a full table.
The Paver Path Calculator does all of this at once: enter your area and paver size (square or rectangular) to get pavers, gravel and sand with your waste margin included. For the installation itself, see how to lay pavers.
Sources: 10-Step Guide to Installing Pavers — OSU Extension.
FAQ
How many 4×8 pavers are in a square foot?
4.5 by nominal size. A 4×8 in paver covers 32 square inches, and a square foot is 144 square inches. Many 4×8 pavers are actually slightly smaller (metric 100×200 mm), which works out to about 4.6 per square foot, so use the coverage on the pallet label when you have it.
How many pavers do I need for a 10×10 patio?
100 square feet. That's 450 of the 4×8 size, 100 of the 12×12 size, or 57 of the 16×16 size before extra for cuts. Add 5–10% on top.
How many pavers are on a pallet?
It depends on the size and brand, so check the supplier's listing. Pallets are usually rated by square feet of coverage, which is easier to plan with than a piece count.
Should I buy extra pavers?
Yes. Oregon State Extension recommends adding 5% for cuts, or 10% if you'll be cutting a lot, such as curves, circles or diagonal patterns. Keeping a few spares also lets you replace a cracked paver later with a matching one.