How to Build a Firewood Rack: Sizes, Cords and Lumber
By Efraín Vega · Published November 6, 2026 · Last updated November 16, 2026

A standard firewood rack is 8 feet long and 4 feet tall. With 16-inch logs it holds 42.7 cubic feet: 1/3 of a cord, also called a face cord. You can build one from four 2×4×8 boards and a pair of rack brackets, set on concrete blocks to keep the wood off the ground.
The rest of this guide covers rack sizes in cords, the lumber list, and how to stack the wood so it dries.
How much firewood does a rack hold?
A full cord is 128 cubic feet of stacked wood: 4 ft high × 4 ft deep × 8 ft long. That's the legal unit for selling firewood in most states under NIST Handbook 130. A rack usually holds one row of logs, so its capacity depends on how long your logs are. Use our Firewood Cord & Face Cord Calculator (or jump to 1 Full Cord and 1 Face Cord / Rick) to check any stack size and BTU heat rating.
Formula: rack length (ft) × stack height (ft) × log length (in) ÷ 12 = cubic feet. Divide by 128 for cords.
| Rack (length × height) | 16-in logs | 18-in logs | 24-in logs |
|---|---|---|---|
| 4 × 4 ft | 21.3 cu ft (1/6 cord) | 24 cu ft (0.19 cord) | 32 cu ft (1/4 cord) |
| 8 × 4 ft | 42.7 cu ft (1/3 cord) | 48 cu ft (0.38 cord) | 64 cu ft (1/2 cord) |
| 12 × 4 ft | 64 cu ft (1/2 cord) | 72 cu ft (0.56 cord) | 96 cu ft (3/4 cord) |
| 16 × 4 ft | 85.3 cu ft (2/3 cord) | 96 cu ft (3/4 cord) | 128 cu ft (1 cord) |
To store a full cord of 16-inch logs, you need 24 feet of 4-ft-high rack: three 8-ft racks, or two rows in a deeper rack.
Buying by the face cord
"Face cord" and "rick" aren't standard units, so two sellers can mean different amounts. Ask for the log length, or the price per full cord. Then use the table: three face cords of 16-in logs equal one full cord.
What lumber do you need for an 8-ft firewood rack?
The simplest build uses a firewood rack bracket kit (two steel brackets sized for 2×4s). The brackets hold the base rails and the uprights, so there are no joints to cut.
| Item | Qty | Use |
|---|---|---|
| Pressure-treated 2×4×8 | 2 | Base rails (left uncut) |
| Pressure-treated 2×4×8 | 2 | Cut in half: four 48-in uprights |
| Firewood rack bracket kit | 1 (2 brackets) | Connects rails and uprights at each end |
| Concrete blocks or solid pavers | 4–6 | Keep the rails off the soil |
| Exterior screws (if the kit uses them) | Per kit | Fasten the boards into the brackets |
| Tarp or rack cover (optional) | 1 | Covers the top of the stack |
Use ground-contact pressure-treated lumber for the base rails: they sit close to damp ground and wet bark all winter. Uprights can be standard treated or cedar.
Want a full wooden version without brackets? Add a 2×4 frame at each end: two uprights joined by 16-in crosspieces at the top and bottom, screwed to the rails. Add a diagonal brace if the rack is taller than 4 ft.
How do you build it?
- Pick the spot. Level, sunny, and open to wind—at least 30 feet from the house if you're in a wildfire-prone area (NFPA Firewise), and never against a wall.
- Set the base. Place two concrete blocks at each end and one or two in the middle, level with each other. For a permanent spot, set them on a 3–4 in pad of compacted gravel so they don't sink. The Gravel Calculator gives the amount for your footprint.
- Cut the uprights. Cut two 2×4×8s in half to get four 48-in pieces.
- Assemble the ends. Slide two uprights and the ends of both base rails into each bracket and fasten them according to the kit.
- Stand it on the blocks and check it's level along the length. A rack that leans gets worse as you stack.
How should you stack firewood so it dries?
- Split first. Split wood dries much faster than rounds.
- Leave gaps. Stack loosely enough for air to move through. A tight stack stays damp in the middle.
- Cover the top only. Keep rain and snow off the top layer, and leave the sides open.
- Stack no higher than about 4 ft on a single-row rack, unless the ends are braced.
- Give it time. EPA's Burn Wise program says properly seasoned wood has been drying for at least 6 months and has a moisture content of 20% or less. A low-cost moisture meter checks a freshly split face.
Building an outdoor cooking station? See our masonry blueprints for an outdoor pizza oven base with built-in firewood alcove.
Don't move firewood long distances
Firewood can carry invasive pests such as the emerald ash borer. Buy or cut wood near where you'll burn it, and follow your state's rules on moving firewood.
Sources: NIST Handbook 130, Uniform Regulation for the Method of Sale of Commodities (firewood); EPA Burn Wise, "Choose the Right Wood"; NFPA Firewise USA, "Preparing homes for wildfire" (home ignition zone).
FAQ
How much wood fits in an 8 ft firewood rack?
An 8 ft long rack stacked 4 ft high holds 32 square feet of stack face. With 16-inch logs that's 42.7 cubic feet, or 1/3 of a cord (one face cord). With 24-inch logs it's 64 cubic feet, half a cord.
What is a full cord of wood?
A cord is 128 cubic feet of wood, ranked and well stowed—a stack 4 ft high, 4 ft deep, and 8 ft long. It's the standard legal unit for selling firewood in most US states (NIST Handbook 130).
What is a face cord?
A face cord (or rick) is a stack 4 ft high and 8 ft long, one log deep. With 16-inch logs it's 1/3 of a full cord. Because it depends on log length, it isn't a standard legal unit—ask the seller for the volume in cubic feet or as a fraction of a cord.
How far should a firewood rack be from the house?
NFPA's Firewise USA program recommends keeping firewood at least 30 feet from the house in wildfire-prone areas. Anywhere, keeping it away from walls also discourages termites and rodents from moving in. Bring indoors only what you'll burn in a few days.
Should you cover firewood?
Cover the top only. A roof or a tarp over the top layer keeps rain and snow off, while open sides let wind and sun keep drying the wood. Wrapping the whole stack traps moisture.



