How Much Does It Cost to Build a Deck? (10x10 & 12x12 DIY Breakdown)
By Efraín Vega · Published October 28, 2026

Building a 10×10-foot deck (100 sq ft) yourself costs between $1,400 and $2,200 in materials for standard pressure-treated pine, compared to $4,500 to $8,500 if you hire a professional contractor.
Stepping up to a 12×12-foot deck (144 sq ft) costs $2,100 to $3,400 in lumber and hardware DIY, while professional installation averages $6,500 to $11,500.
Below is the complete, itemized Bill of Materials (BOM) and cost comparison for both sizes, covering footings, structural framing, fasteners, and decking boards.
To customize your exact board counts and screw quantities, run your dimensions through our interactive Deck Calculator.
How much does it cost to build a 10×10 deck DIY?
Building a 10×10-foot deck yourself costs $1,400 to $2,200 in materials ($14 to $22 per square foot) using pressure-treated pine. Upgrading to Western Red Cedar runs $2,800 to $4,200, while composite decking (such as Trex) costs $3,800 to $5,800. Professional contractor installation averages $4,500 to $8,500.
| Deck Size | Pressure-Treated Pine (DIY) | Western Red Cedar (DIY) | Composite Decking (Trex DIY) | Contractor Turnkey Cost |
|---|---|---|---|---|
| 10×10 ft (100 sq ft) | $1,400 – $2,200 | $2,800 – $4,200 | $3,800 – $5,800 | $4,500 – $8,500 |
| 12×12 ft (144 sq ft) | $2,100 – $3,400 | $4,100 – $6,100 | $5,500 – $8,200 | $6,500 – $11,500 |
| 16×20 ft (320 sq ft) | $4,600 – $7,200 | $9,000 – $13,500 | $12,200 – $18,000 | $14,500 – $26,000 |
Estimates reflect 2026 retail home improvement pricing including structural hardware, footings, and 10% cutting waste.
Complete Bill of Materials for a 10×10 Ground-Level Deck
This material takeoff is for a sturdy, code-compliant freestanding platform deck built with pressure-treated Southern Yellow Pine or Douglas Fir:
| Component | Specification | Quantity Needed | Est. Unit Cost | Total Est. |
|---|---|---|---|---|
| Footings | 10" Sonotube forms + 80-lb concrete | 4 holes (8 bags total) | $7.50 / bag | $60 |
| Support Posts | 4×4 Ground Contact Treated (8 ft) | 2 posts (cut in half) | $16.00 | $32 |
| Post-to-Beam Caps | Simpson Strong-Tie BC40 brackets | 4 brackets | $11.50 | $46 |
| Drop Beam | Double 2×10 × 10 ft boards | 4 boards (laminated) | $22.00 | $88 |
| Floor Joists | 2×8 × 10 ft (16" O.C. spacing) | 9 joists | $15.50 | $140 |
| Rim Joists | 2×8 × 10 ft perimeter bands | 2 boards | $15.50 | $31 |
| Joist Hangers | Simpson LUS28 ZMAX galvanized | 14 hangers | $2.10 | $30 |
| Decking Boards | 5/4×6 in × 10 ft Premium Treated | 22 boards (incl. waste) | $12.50 | $275 |
| Structural Fasteners | ½" × 6" Galvanized carriage bolts | 12 bolts + washers | $3.50 | $42 |
| Deck Screws | #9 × 3" Exterior ceramic coated | 5-lb bucket (≈ 700 screws) | $48.00 | $48 |
| Hardware Nails | 1½" 10d Joist hanger teco nails | 1 box (250 nails) | $18.00 | $18 |
| Fascia Trim | 1×8 × 10 ft Cedar or Primed band | 4 boards | $19.00 | $76 |
| Total DIY Estimate | $886 – $1,450 |
Adding stairs and perimeter guardrails adds approximately $350 to $650 in balusters and 4×4 corner posts.
12×12 Deck Material Takeoff Adjustments
Stepping up from 10×10 to 12×12 adds 44% more square footage (144 sq ft vs 100 sq ft). Here is what changes in your framing specs:
- Joist Count: Spaced at 16 inches on-center, a 12-foot wide deck requires 11 field joists plus 2 rim joists (total 13 boards).
- Joist Sizing: For a 12-foot clear span, code typically requires 2×8 or 2×10 lumber depending on your local snow load (40 lbs/sq ft live load). Refer to our Deck Joist Spacing and Span Tables for maximum spans.
- Decking Boards: With 5.5-inch wide boards and a ¼-inch gap, you need 28 deck boards (12-foot stock), or approximately 900 linear feet of decking.
- Footings: Increase to 6 concrete footings (two 3-post beam rows) to prevent bounce and center deflection over the longer 12-foot span. Calculate exact bag counts with our Concrete Footing Calculator.
3 Critical Framing Rules That Prevent Deck Failure
1. Never Fasten Joists With Standard Drywall or Gold Wood Screws
Standard construction screws lack shear strength. Under live foot traffic or winter snow loads, their brittle heads snap clean off. Always use code-approved #9 or #10 structural wood screws (like FastenMaster TimberLOK) or hot-dipped galvanized 10d connector nails in joist hangers.
2. Guard Against Flashing Corrosion (ZMAX / Stainless Steel)
Modern pressure-treated wood uses high concentrations of micronized copper azole (MCA), which aggressively corrodes standard steel. All joist hangers, bolts, and nails must have a G90 hot-dipped galvanized coating (labeled ZMAX) or be made of 304/316 stainless steel.
3. Account for Board Moisture When Setting Gaps
- Kiln-Dried Wood or Composite: Boards will expand when exposed to humidity. Space them with a clean 3/16" to 1/4" gap using a carpenter's pencil.
- Wet Pressure-Treated Lumber: Often arrives soaking wet from the chemical treatment plant. Install wet boards butt-tight together; as they dry out over the first 60 days of summer, they naturally shrink and form a perfect 1/8" drainage gap.
Sources: American Wood Council: Prescriptive Residential Wood Deck Construction Guide (DCA 6), International Residential Code (IRC) Chapter 5: Floors.
FAQ
How much does it cost to build a 10x10 deck yourself?
Building a 10×10 ft (100 sq ft) deck yourself costs between $1,400 and $2,200 using pressure-treated pine ($14–$22/sq ft). Upgrading to natural Western Red Cedar costs $2,800 to $4,200 ($28–$42/sq ft), while composite decking (such as Trex) runs $3,800 to $5,800 ($38–$58/sq ft).
How much cheaper is it to build a deck yourself vs hiring a contractor?
Labor accounts for roughly 50% to 65% of professional deck quotes. Contractors typically charge $45 to $85 per square foot installed ($4,500–$8,500 for a 10×10 deck). Doing the labor yourself cuts the total project cost in half.
What materials do I need for a 10x10 deck?
A freestanding 10×10 deck requires: 4 concrete footings (8–12 bags of 80 lb concrete), two 2×10 drop beams, 9 pressure-treated 2×8 floor joists (spaced 16 inches O.C.), two 2×8 rim joists, 20 five-quarter (5/4×6) deck boards (10 ft lengths), 14 joist hangers, and about 700 exterior deck screws.
How many joists do I need for a 12x12 deck?
A 12×12 ft deck with joists spaced at the standard 16 inches on-center requires 11 floor joists plus 2 outer rim joists, for a total of 13 joists (2×8 or 2×10 lumber).



